kevycito

05 / Guide

Track your swing

How to film and measure your own swing with a phone. A tripod, some light and a free tool are enough to start.

01 / Contents

In this guide

Set up once, film a few swings, then count frames. Each step below links straight to its section.

02 / What you need

Three things

No special gear. If your phone can film slow motion, you already own the hard part.

Camera

A phone that films 240 fps slow motion

Most recent phones do. Look for a slow motion mode in the camera app and set it to 240 frames per second.

Support

A tripod or a fence clamp

The phone must not move while you swing. A hand held phone shakes, and shake ruins every measurement.

Light

Good light

Film outdoors or in a bright cage. Slow motion uses very short exposures, so dim light gives dark, grainy frames.

03 / Camera setup

Where the camera goes

Two views answer different questions. The side view is the main one. Add the behind view when you can.

Top view of home plate, a hitter and two camera spots. The side camera sits square to the hitting line, 15 to 20 feet from the hitter. The behind camera sits straight down the line, behind the net. Illustration, not to scale To the pitcher Plate Hitter Side camera Hip height 15 to 20 ft Net Behind camera
Illustration. Top view, not to scale.

Side view

  • Put the camera square to the hitting line, which runs from the pitcher to the plate.
  • Set the lens at about hip height, roughly 15 to 20 feet from the hitter.
  • Keep the whole body and the bat in frame, with room for the stride and the finish.
  • Film in landscape and keep the phone level, so angles on screen are true.

Behind view

  • Put the camera straight down the hitting line, behind the hitter, with the net between you.
  • Use it for how the body and bat sit against the line, how the shoulders and hips rotate and how the head moves side to side.
  • Same height, same slow motion setting, same light.

Mark the tripod legs with tape so you can put the camera back in the same spot next time.

04 / Scale

Give the screen a ruler

Pixels mean nothing until you know how long something real is. Put one known length in frame.

Home plate is 17 inches wide. If it is in your frame, it is your ruler. If it is not, lay a stick of known length on the ground in frame, such as a bat or a measured length of board.

Measure the known length on screen, then divide. Here is a worked example with round numbers, not a measurement. If a 17 inch plate spans 340 pixels, that is 20 pixels per inch. A stride that spans 600 pixels is then 30 inches.

One catch: the ruler only works at its own distance from the lens. Things closer to the camera look bigger. Lay the stick on the ground at the hitter's feet, in the same line as the stride, and measure along that line.

Home plate width

17 in

Use it as your ruler when the plate is in frame.

05 / Setup checklist

Before you film

Tick these off as you go. The boxes reset when you reload the page.

06 / What to measure

Frame by frame

Step through the clip one frame at a time. Pick the same marker every swing, so numbers stay comparable.

Frame length at 240 fps

4.2 ms

Frame length at 120 fps

8.3 ms

Home plate width

17 in

Side view

Stride length and timing

Measure how far the front foot travels, using your scale. Count the frames from the front foot starting to move until it lands.

Both views

Head movement

Pick a spot on the head or cap. Mark where it sits at the start and at contact. The gap is how far the head moved.

Side view

Hand path

Follow the hands from the load to contact, frame by frame. Note whether they travel straight toward the ball or loop out first.

Side and behind

Bat path and attack angle

Draw the path of the bat head around contact. Attack angle is the angle of that path against level ground at contact.

Behind view

Hip and shoulder turn, and their order

Measure how far the hips and the shoulders each turn, and note which starts first. Most coaching wants the hips to lead.

Any view

Launch to contact time

Pick a launch marker, such as the first frame the hands move forward. Count frames to contact. At 240 fps, multiply by 4.2 ms. Thirty frames is about 125 ms.

07 / Free tools

What to review with

You do not need to pay for software to measure a swing.

Free and open source

Kinovea

A free video analysis tool for Windows. It measures angles, distances and timing on video, so it covers most of the list above.

Get Kinovea (opens in a new tab) ↗

Already on your phone

The phone's own player

Most players let you drag the slider slowly to step through a clip. That is enough to count frames and spot big problems. For angles and distances, use a tool like Kinovea.

08 / Swing log

Write it down

A number you did not write down is a number you will argue about later. Copy this table into a note or a spreadsheet.

Swing log
Date Drill Swings filmed Stride Head movement Launch to contact (frames) Notes
YYYY-MM-DDName of the drillCountin or cmin or cmCountOne short line

09 / How often to re-film

Same spot, every time

One session tells you where you are. Two sessions tell you which way you are moving.

  • Re-film every couple of weeks while you are working on something.
  • Re-film after any change: a new drill, a new stance, a new bat.
  • Put the camera in the same spot, at the same height, in similar light. Use your tape marks.
  • Film the same number of swings each time, and log them the same way.
  • Compare clips side by side, and compare numbers in the log. Trust a change that shows up in several swings, not in one.

Keep one thing steady. If you change the camera spot, the drill and the bat in one session, you cannot tell which change moved the numbers.

10 / Next

Get it read

Counting frames by hand works. It is also slow.

Send the clips for a breakdown

Film the angles above and send them in. Offspeed Analytics reads the swing and sends back two versions: the full audit and a one-page simple card.